{"id":44748,"date":"2023-05-17T14:50:48","date_gmt":"2023-05-17T14:50:48","guid":{"rendered":"https:\/\/c01.purpledshub.com\/bbcskyatnight\/?post_type=purple_issue&p=44748"},"modified":"2023-05-30T12:13:56","modified_gmt":"2023-05-30T12:13:56","slug":"diy-astronomy-build-your-own-eq-camera-mount","status":"publish","type":"post","link":"https:\/\/c01.purpledshub.com\/bbcskyatnight\/2023\/05\/17\/diy-astronomy-build-your-own-eq-camera-mount\/","title":{"rendered":"DIY Astronomy: Build your own EQ camera mount"},"content":{"rendered":"\n
Practical astronomy projects for every level of expertise <\/p>\n\n
DIY Astronomy <\/span><\/h1>\n\n\n\n
Build your own EQ camera mount<\/strong><\/h4>\n\n
A DIY equatorial mount to help you point your camera for astrophotography <\/p>\n\n
Your mount will hold a standard DSLR, with simple \u2018setting circles\u2019 to help you aim <\/figcaption><\/figure><\/div>\n\n
This month\u2019s project is a manual equatorial mount that is enjoyable to use and helps to develop your knowledge of the night sky. Using RA and dec. (Right Ascension and declination) coordinates, it is possible to locate a faint target that might otherwise be difficult to see in your viewfinder. With an undriven mount, you are limited to relatively short exposures, but with a fast lens and high ISO setting, impressive night-sky images are certainly achievable. <\/p>\n\n
The mount\u2019s RA axis must be aligned with Earth\u2019s axis of rotation, so you must adapt the downloadable plans to suit your latitude. At the North or South Poles, the RA axis would point vertically upwards, and at the equator it would be horizontal. For most of us, the angle between the RA disc and the ground is somewhere in between (90\u00b0 minus your latitude). <\/p>\n\n
Wrangle the angles <\/strong><\/h4>\n\n
The dec. assembly pivots on the RA disc, but it is clampable with a wing nut when you\u2019re ready to take a photo. Similarly, the camera platform pivots on the dec. assembly, also with a clamp. The dec. scale is glued so that it reads 90\u00b0 when the camera is pointing directly at the Pole. As the night sky appears to rotate, the RA scale must be free to turn, so you can adjust it. A strong bulldog clip holds it still while you move the dec. assembly between targets. <\/p>\n\n
To use the mount, it must firstly be polar aligned. Make sure the base is level, with the RA disc facing due north (in the Northern Hemisphere). To fine-tune the alignment, you can place a smartphone (with a planetarium app) on the RA disc and centre the displayed south celestial pole. <\/p>\n\n
Next you need to move both axes so that the camera\u2019s viewfinder is centred on a known bright star (we\u2019ll use Vega as an example: RA 18h 37m, dec. +38.8\u00b0). The dec. scale should automatically read very close to 39\u00b0. Turn the RA scale so that it shows as close to 18 hours and 37 minutes as possible, then clamp it with the bulldog clip. Now you are ready to find your next target. Turn the camera (taking care not to dislodge the RA scale) to the coordinates of your new target and re-clamp the axes. <\/p>\n\n
You can\u2019t do anything to adjust the image frame\u2019s orientation, but if your camera ends up awkwardly positioned, you can rotate both axes a full 180\u00b0 to achieve a more acceptable setup (the dec. scale is repeated in both directions, and the RA disc has two pointers 180\u00b0 apart). <\/p>\n\n
Periodically you will need to adjust the RA scale to reflect Earth\u2019s rotation, but if you dial in the coordinates for the object that you are currently aiming at, you will have plenty of time to move to the next. <\/p>\n\n
Place the mount on a flat surface or on a regular photography tripod <\/figcaption><\/figure><\/div>\n\n
<\/div>
\n
What you\u2019ll need <\/strong><\/h4>\n\n\n\n
\u2022 Drill with bits: 6mm for the pivots, plus some larger ones to remove unnecessary plywood to save some weight \u2022 Marking out tools, coping saw, scissors, craft knife, pencil, clamps \u2022 15mm good-quality plywood or similar (approximately 500 x 500mm) \u2022 Two M6 x 40mm bolts (with wing nuts and washers) \u2022 Stiff wire for the pointers \u2022 Inexpensive tripod mount and camera plate, or 1\/4-20 threaded screws \u2022 Large bulldog clip to hold the RA scale \u2022 Spray paint, wood glue <\/p>\n<\/div><\/section>\n\n
Step by step<\/h4>\n\n
<\/figure><\/div>\n\n
Step 1 <\/strong><\/h5>\n\n
Using our downloadable plans (adjusting them for your latitude), carefully mark out all the parts. By \u2018nesting\u2019 the shapes, you\u2019ll be able to make efficient use of the board. Mark the centres of the pivots for drilling by pushing a sharp point into the wood. <\/p>\n\n
<\/figure><\/div>\n\n
Step 2 <\/strong><\/h5>\n\n
Carefully cut out the pieces. A coping saw is fine, but if you have a jigsaw or bandsaw, you can speed things up. You could tape the two sloping base parts together while cutting, so that they come out identical. Sand all the parts smooth. <\/p>\n\n
<\/figure><\/div>\n\n
Step 3 <\/strong><\/h5>\n\n
Drill the central 6mm-diameter pivots holes, then use larger drills to remove unnecessary plywood to keep the overall weight down. If you space these carefully, they can look aesthetically pleasing too! We chamfered all of the edges as well. <\/p>\n\n
<\/figure><\/div>\n\n
Step 4 <\/strong><\/h5>\n\n
The three main parts all need to be glued together. A good selection of clamps helps, but you can get by with masking tape. You can use dowels or screws to strengthen the joints, but be sure to drill pilot holes or the wood might split. <\/p>\n\n
<\/figure><\/div>\n\n
Step 5 <\/strong><\/h5>\n\n
Print off and cut out the scales (we laminated ours too), with punched central holes for the pivots. We used thin wire to make our pointers. We drilled small holes in the edge of the wood and pushed them in, then bent and cut them to size. <\/p>\n\n
<\/figure><\/div>\n\n
Step 6 <\/strong><\/h5>\n\n
After a final sanding, carefully paint or varnish your parts. After assembly, we added an inexpensive tripod mount to hold the camera and a camera plate that fitted our tripod. Alternatively, use 1\/4-20 threaded screws to hold the camera to good effect. <\/p>\n\n
![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/main-image_preview-1024x768.jpg\")
![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/second-image_preview-1024x907.jpg\")
![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/1-marking-out-1024x594.jpg\")
<\/figure><\/div>\n\n![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/2-cutting-out-1024x593.jpg\")
<\/figure><\/div>\n\n![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/3-drilling-1024x593.jpg\")
<\/figure><\/div>\n\n![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/4-gluing-2-1024x593.jpg\")
<\/figure><\/div>\n\n![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/5-cutting-scales-1024x594.jpg\")
<\/figure><\/div>\n\n![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2023\/05\/6-painting-2-1024x594.jpg\")
<\/figure><\/div>\n\n![\"\"](\"https:\/\/c01.purpledshub.com\/uploads\/sites\/77\/2022\/10\/Layer-20-1024x1024.png\")